| 162.45.2366.891.41.1503 Standard 5 Slewing Ring Bearings | d:15 mm; D:35 mm; rs (min):0.6 mm; da:19 min; a:23 mm; Bearing designation:3202 ; Da:30 max; Weight:0.07 kg; Grease:13 000 min-1; Oil:16 000 min-1; Dynamic (Cr):10.381 kN; ra:0.6 max; B:15.9 mm; Static (Cor):7.500 kN; Pu:0.341 kN; |
| 21 0541 01 Rollix Slewing Ring Bearings | l3 min.:68 mm; r1 min.:0.6 mm; G:M 52x3; d2 max.:114 mm; Mass rod end:4.1 kg; h1:195 mm; B:35 mm; Specific dynamic load factor K:100 N/mm²; d:50 mm; C1 max.:31 mm; Basic dynamic load rating C:156 kN; Material constant KM:330; l4 max.:254 mm; α:6 °; l7 min.:60 mm; d4 ≈:70 mm; Basic static load rating C0:270 kN; l5 ≈:30 mm; w:60 mm; dk:66 mm; |
| 192.40.4500.990.41.1502 Standard 5 Slewing Ring Bearings | D:175.0000 mm; Basic Dynamic Radial Load Rating C:185000 N; Basic Static Radial Load Rating Co:228000 N; Grease Speed Rating n1:2900 rpm; Oil Speed Rating n2:3500 rpm; Fillet Radius ra:2.00 mm; B:60.00 mm; d:110.000 mm; Fillet Radius rb:1.00 mm; |
| 192.40.3550.990.41.1502 Standard 5 Slewing Ring Bearings | Grease Speed Rating n1:2000 rpm; Fillet Radius rb:1.00 mm; B:90.00 mm; Basic Dynamic Radial Load Rating C:276000 N; Oil Speed Rating n2:3000 rpm; d:95.000 mm; Basic Static Radial Load Rating Co:300000 N; Fillet Radius ra:2.50 mm; D:200.0000 mm; |
| 11.50.3567.001.49.1502 Standard 5 Slewing Ring Bearings | H1:169.875 mm; Cap bolt, SAE grade:8; Initial grease fill:793.8 g; dc:153.988 mm; A2:225.425 mm; R2:33.337 mm; Labyrinth ring (db shaft position):LOR 156; db:177.8 mm; Cap bolt recommended tightening torque:813.5 N·m; Housing:SSAFS 232; Bearing limiting speed:2800 r/min; H2:66.675 mm; A1:158.75 mm; P60°:345 kN; P120°:133 kN; Mass pillow block:125 kg; Labyrinth ring (dc shaft position):LOR 142; |
| 161.28.1700.890.11.1503 Standard 5 Slewing Ring Bearings | Grease Speed Rating Open/Shielded n1:11000 rpm; Basic Static Radial Load Rating Co:6800 N; d:35.000 mm; Fillet Radius ra:0.64 mm; Accessories:One Shield; B:10.00 mm; Sealed Speed Rating n3:7500 rpm; D:55.0000 mm; Basic Dynamic Radial Load Rating C:9560 N; Oil Speed Rating Open/Shielded n2:14000 rpm; |
| 162.40.2128.890.11.1503 Standard 5 Slewing Ring Bearings | B:57.15 mm; Keyway e:58.4 mm; Oil Mist Speed Rating Max. n3:6000 rpm; Fillet Radius ra:2.00 mm; Oil Speed Rating Max. n2:3500 rpm; d:57.150 mm; X-L-O Part Number:115-37; Preload:200 lb; Keyway f:4.7 mm; D:120.7000 mm; Grease Speed Rating Max. n1:2200 rpm; |
| 191.32.2500.990.41.1502 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:43000 N; d:40.000 mm; B:39.70 mm; Grease Speed Rating n1:5000 rpm; D:90.0000 mm; Basic Dynamic Radial Load Rating C:60500 N; Oil Speed Rating n2:6700 rpm; Accessories:Two Shields; Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:5000 rpm; |
| 121.32.3750.990.41.1502 Standard 5 Slewing Ring Bearings | d1 ≈:73.5 mm; Cb min.:6 mm; Basic static load rating C0:200 kN; Calculation factor e:0.35; r1,2 min.:2.5 mm; T:36 mm; Ca min.:6 mm; d:50 mm; Limiting speed:6700 r/min; rb max.:2.5 mm; ra max.:2.5 mm; Db min.:94 mm; da max.:59 mm; Basic dynamic load rating C:189 kN; db min.:61 mm; r3,4 min.:2.5 mm; B:35 mm; Da max.:90 mm; Reference speed:5600 r/min; C:30 mm; |
| 192.25.2800.990.41.1502 Standard 5 Slewing Ring Bearings | G:M 30x2; Mass rod end:0.9 kg; α:6 °; Basic static load rating C0:81.5 kN; B:22 mm; l2 max.:149 mm; d:30 mm; r1 min.:0.6 mm; Basic dynamic load rating C:62 kN; l7 min.:34 mm; h:110 mm; C1 max.:20 mm; Material constant KM:330; Specific dynamic load factor K:100 N/mm²; dk:40.7 mm; d2 max.:75 mm; l1 min.:65 mm; |
| 11.40.2795.000.11.1502 Standard 5 Slewing Ring Bearings | Basic static load rating C0:11.4 kN; Calculation factor X:0.41; Limiting speed:26000 r/min; Calculation factor Y1:0.92; Calculation factor e:0.68; Calculation factor A:0.000656; a:16 mm; D1 ≈:41.66 mm; Calculation factor kr:0.095; ra max.:1 mm; Mass bearing:0.13 kg; r1,2 min.:1 mm; d1 ≈:35.8 mm; Da max.:46.4 mm; da min.:30.6 mm; Calculation factor Y0:0.76; d2 ≈:30.773 mm; B:15 mm; |
| 12.35.2690.000.11.1503 Standard 5 Slewing Ring Bearings | B:6 mm; d:5 mm; Tolerance housing:H7; Specific dynamic load factor K:25 N/mm²; Specific static load factor K0:45 N/mm²; D:10 mm; D1:12 mm; Tolerance shaft:e7; B1:2 mm; Coefficient of friction µ max.:0.15; Permissible sliding velocity v max.:0.5 m/s; Permissible sliding velocity v min.:0 m/s; Mass bushing:0.003 kg; Coefficient of friction µ min.:0.08; |